NEC Server 320Fd Systems User Manual
Read Me First: Unpacking  
Express5800/320Fd Systems  
NEC Corporation of America  
456-01742-000  
 
Contents  
Introduction  
1
4
4
6
6
Before Unpacking the System  
Unpacking the System  
Disposing of Packing Materials  
What to Do Next  
-iii-  
 
-iv-  
 
Introduction  
Read Me First: Unpacking Express5800/320Fd Systems  
explains how to unpack a system from its shipping box.  
W A R N I N G  
!
To avoid eye and skin injuries, be careful  
when cutting the shipping straps from the  
shipping box. The straps can snap with  
considerable force when cut.  
W A R N I N G  
!
To avoid back injury, do not attempt to remove  
an enclosure before you remove the shipping  
box from the shipping pallet. When the  
shipping box is removed, lift and remove each  
enclosure with the assistance of another  
person.  
W A R N I N G  
!
To avoid back injury, enlist the assistance of  
another person to lift and remove the  
enclosures and pedestal case.  
-1-  
 
Figure 1 shows the packaged components, and the order in which  
to remove them, for a rack-mounted system. Figure 2 shows the  
packaged components, and the order in which to remove them, for  
a pedestal system.  
Figure 1. Unpacking a Rack-Mounted System  
1
2
3
4
5
asys072  
1
Accessories box  
Shipping box  
2
3
Shelf unit  
4 and 5  
CPU-I/O enclosures  
-2-  
 
Figure 2. Unpacking a Pedestal System  
1
2
3
4
5
asys073  
1
Pedestal case  
2
Accessories box  
Shipping box  
3
4 and 5  
CPU-I/O enclosures  
-3-  
 
Before Unpacking the System  
• Check the label or the packing slip on the outside of the  
shipping box to verify that you received the correct shipment.  
Depending on your order, you have received either a  
rack-mountable system or a pedestal system.  
• Verify that the Tip-N-Tell and Shockwatch indicators on the  
outer sides of the shipping box are not activated.  
C A U T I O N  
!
Do not unpack the system if you did not receive  
the correct shipment, or if an indicator on the  
shipping box is activated. Contact the shipping  
carrier and the purchasing agent for your system  
immediately.  
Unpacking the System  
Tools needed: A pair of scissors or a utility knife  
1. Place the shipping box in the location where the system will be  
installed, leaving it right side up on its shipping pallet.  
2. Use the scissors or knife to cut the shipping straps and remove  
them from the shipping box. To avoid injury while cutting each  
strap, hold the strap firmly with one hand as you stand away  
from it.  
W A R N I N G  
!
To avoid eye or skin injuries, be careful when  
cutting the straps from the box. The straps  
can snap with considerable force when cut.  
-4-  
 
   
3. Open the top cardboard flaps of the shipping box by cutting  
through the taped portion of the flaps to release them.  
4. If you have received a pedestal system, remove the pedestal  
case, place it on a table or other sturdy surface, and remove  
its foam packaging material.  
W A R N I N G  
!
To avoid back injury, lift and remove the  
pedestal case with the assistance of another  
person.  
5. Remove the accessories box. Open the accessories box and  
make sure that it contains (along with other items) the  
Express5800/320Fd: Setup Guide.  
6. Lift and remove the shipping box from the shipping pallet.  
W A R N I N G  
!
To avoid back injury, do not attempt to remove  
the shelf unit or enclosures before you  
remove the shipping box from the shipping  
pallet.  
7. If you received a rack-mountable system, remove the shelf  
unit and place it on a table or other sturdy surface and remove  
its foam packaging material.  
-5-  
 
8. Remove each CPU-I/O enclosure, one at a time, from the  
shipping pallet. Pull the foam blocks away from the first  
enclosure and remove it. Then, do the same for the second  
enclosure.  
W A R N I N G  
!
To avoid back injury, lift and remove each  
enclosure with the assistance of another  
person.  
9. Remove the enclosures from their plastic bags, then place the  
enclosures flat on a table or other sturdy work surface near the  
installation area.  
Disposing of Packing Materials  
The packing materials do not contain any hazardous compounds.  
Dispose of them according to applicable procedures or local  
regulations.  
If, however, you decide to retain the undamaged container and its  
packing materials, you can use them to ship the system at a later  
time.  
What to Do Next  
To install the system, see the Express5800/320Fd: Setup Guide.  
-6-  
 
   

Multiquip Automobile Parts C 30HDNI User Manual
Murray Snow Blower 1695720 User Manual
NAD Universal Remote HTR 2 User Manual
NEC Flat Panel Television PX 42VP4DP A User Manual
NetComm Network Router NP720 User Manual
NETGEAR Network Router R6200 100NAS User Manual
NeumannBerlin Microphone Digital Microphones For High Resolution Audio User Manual
Oki All in One Printer 510W User Manual
Optoma Technology Projector Digital Tuner Output Projector User Manual
Oster Waffle Iron CKSTWF40 User Manual